![]() autogen.sh (with or without -enable-opengl) I get OpenCL.: NOT FOUND. OpenGL version string: 7 Compatibility Profile Context 13.101 OpenGL renderer string: AMD Radeon HD 6900 Series OpenGL vendor string: Advanced Micro Devices, Inc. Memory at fb9fc000 (64-bit, non-prefetchable) įglrxinfo results are: display: :0 screen: 0 System run well about first 15 minutes and then the Blue Fury miners will 'dead'. The HW setup is 3x Blue Fury and 3x Asic USB miners connected to powered USB hub. Cayman/Antilles HDMI Audio įlags: bus master, fast devsel, latency 0, IRQ 50 Posts: 2 Joined: Fri 3:43 pm cgminer/bfgminer problem Fri 4:00 pm Hi, i have problem with both common mining programs. Expansion ROM at fb900000 Ġ4:00.1 Audio device: Advanced Micro Devices, Inc. Memory at fb9c0000 (64-bit, non-prefetchable) So arrange a working ssh cable to get started with the installation method. Without an ssh cable, you cannot proceed with the procedure. Memory at c0000000 (64-bit, prefetchable) Arrange ssh cable: To install cgminer on your raspberry pi, you have to connect the raspberry pi with an appropriate ssh cable. Device 1b2aįlags: bus master, fast devsel, latency 0, IRQ 52 Memory at fbafc000 (64-bit, non-prefetchable) Ġ4:00.0 Display controller: Advanced Micro Devices, Inc. ![]() Cayman/Antilles HDMI Audio įlags: bus master, fast devsel, latency 0, IRQ 49 Expansion ROM at fba00000 Ġ3:00.1 Audio device: Advanced Micro Devices, Inc. No devices detected (cgminer) Wed 4:21 pm Because of the troubles I had earlier today I had to reinstall Raspbian and cgminer. Memory at fbac0000 (64-bit, non-prefetchable) Memory at d0000000 (64-bit, prefetchable) Device 0b2aįlags: bus master, fast devsel, latency 0, IRQ 51 When I run lcpci -v I do see my card: 03:00.0 VGA compatible controller: Advanced Micro Devices, Inc. The emulated data pin is pin 5 on the ESP.When I run cgminer -n(version 3.12.2) I get: USB all: found 12 devices - listing known devices After trying numerous times it finally worked No more need to download it from this website, got it. Īttached you will find a picture of my current breadboard wiring. 1 Update: sudo apt-get install bfgminer failed several times, as the same for sudo apt-get install cgminer. The only thing showing up is the w1_bus_master_1. I also double-checked the behavior with a raspberry Pi 3: Same result. ![]() The device tree debug log also never shows any errors related to 1-wire.Īs far as I understand the topic, the emulated sensor should be at least appear in the /sys/bus/w1/devices/ folder. This is one I found on a forum that got it to work: sudo apt-get install ocl-icd-opencl-dev. Most of the opencl installs uninstall fglrx and install nvidia drivers. I tried a lot of different approaches like using OWFS, different GPIO Pins, and loading kernel modules like w1-gpio and w1-temp. As dobey said I needed opencl, but the amd-sdk versions of opencl did not seem to work for me (I was probably installing them incorrectly). When I remove the 4.7k pullup resistor, random devices appear on the Pi, but with the pullup connected, nothing happens. That means, the wiring must be correct at least and GPIO4 is working. Perhaps you can let us know if you have another BLE device such as HC10 BLE serial adapter between Rpi and Android phone. Now you can transfer files using an 'transfer files' app, or 'FTP server' app. When using this method, the sensor is detected and readings are possible. If your Rpi has successfully 'paired' with the Android device, say an android smart phone, then they are 'connected'. I then tried "bitbanging" GPIO4 directly via this code: Sadly, the device never shows up on the /sys/bus/w1/devices/ folder on the Pi using the standard w1 driver. I can get readings via a connected ESP32 running micropython. In order to resolve, proceed with the following: cd /var/www/minera sudo nano buildminer. Sticking to the basics I started emulating a DS18B20. 1 Answer Sorted by: 0 Ok, any hardware additions to an existing Raspberry Pi Minera environment or any adjustments to the hardware parameters specified in Minera Settings > Manual-options do indeed require recompiling cgminer. To make sure the implementation will work on firsthand, I started with emulating different 1-Wire devices with an ESP8266 and using this library: įor wiring and setting up the Pi, I followed this article: Īlso tried the steps with a vanilla Raspbian install. The goal is to use a Maxim Integrated Max17313 Fuel Gauge for inspecting battery usage. For a project I want to implement 1-Wire communication in a Raspberry Pi Zero W.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |